Fast-fluid GA450 User Manual

V. 2.2Fast & Fluid Management B. V.PO Box 2202170 AE SassenheimThe Netherlandswww.fast-fluid.comManual GA450

10Safety GA450 V. 2.2

Operator manual GA450 V. 2.2113 Operator manual3.1 Description3.1.1 Overview of the machineA: DoorB: CasingC: Control panel. See also § 3.1.2.D: Emer

12Operator manual GA450 V. 2.23.1.2 Overview of the control panelA: Stop/Up keyB: Program keyC: T1 key (Time 1)D: T2 key (Time 2)E: T3 key (Time 3)F:

Operator manual GA450 V. 2.2133.2 Operation3.2.1 Turning on the machine1. Connect the power cable to the grouned wall socket. 2. Make sure that the e

14Operator manual GA450 V. 2.2Place the can1. Put one or more cans (A) in the centre of the can table, or in a pattern that has its gravitational cen

Operator manual GA450 V. 2.215Close the door1. Pull up the handle (A) to unlock the can table.2. Push the can table (B) inwards until you hear a ‘cli

16Operator manual GA450 V. 2.23.2.7 Stop the operation manually1. Push the Stop/Up key. 2. Wait until the can plates are open.3. If necessary, remove

Operator manual GA450 V. 2.217A: Speed (rpm)B: Can height (cm)3.2.9 Adjust the mix time/i250200150100SP1SP2SP3SP450010 20 30 40 50A (rpm)B (cm)Switch

18Operator manual GA450 V. 2.21. At the same time, push the Program key and the T1, 2 or 3 key. 2. Push the + or - key to adjust the mix time for T1,

Operator manual GA450 V. 2.2193.6 Remove spilled paint Do this procedure when paint is spilled inside the machine.1. Make sure that the machine is st

2© Fast & Fluid Management B.V.This manual or parts thereof may not be reproduced, stored in a retrieval system, or transmitted, in any form or by

20Operator manual GA450 V. 2.2

Installation GA450 V. 2.2214 Installation4.1 Unpack the machine4.1.1 Remove the cardboard1. Remove the tensioning straps (A). 2. Remove the cardboard

22Installation GA450 V. 2.24.1.3 Remove the transport brackets1. Remove the screws (A).2. Remove the transport brackets (B).4.1.4 Dispose of the packa

Installation GA450 V. 2.2234.2.2 Move the machine to the final location1. Push the machine to the final location. 2. Connect the power cable to the ne

24Installation GA450 V. 2.2

Troubleshooting GA450 V. 2.2255 Troubleshooting5.1 General troubleshooting procedure1. Try to solve the problem with the information in this manual. S

26Troubleshooting GA450 V. 2.25.3 Troubleshooting guide5.3.1 Easy-to-solve errors5.3.2 Clamp plate errors5.3.3 Inverter errorsProblem Possible cause P

Troubleshooting GA450 V. 2.2275.3.4 Software errors5.4 Reset after an emergency stop1. Unlock the emergency stop.2. Push the Stop/Up key. When the mac

28Troubleshooting GA450 V. 2.2

Technical data GA450 V. 2.2296 Technical data6.1 General specifications/i6.2 Dimensions and mass/i6.3 Ambient conditions/i6.4 Noise level/iParameter

Table of Contents 3Table of Contents1 About this manual...

30Technical data GA450 V. 2.26.5 Safety classifications/i6.6 Electrical specifications/iParameter SpecificationIP (Ingress Protection) classification

Technical data GA450 V. 2.2316.7 Electrical diagram5544332211D DC CB BA AINVERTERCONTROL BOARD24VDC POWERDISPLAY/KEYBOARDOPTICAL SENSORSFILTERCENTRAL

32Technical data GA450 V. 2.2

4Table of Contents 4 Installation ...2

About this manual GA450 V. 2.251 About this manualThe manual shows the information necessary to:-install- operate- perform basic maintenance- correct

6About this manual GA450 V. 2.2

Safety GA450 V. 2.272 Safety2.1 Intended useThe machine is designed to mix paint in a can. Any other use of the machine is strictly forbidden.2.2 Liab

8Safety GA450 V. 2.22.5 Safety symbols on the machine/i2.6 Labels on the machine/i2.7 Safety symbols in the manual/iRead the manual. Electrical hazard

Safety GA450 V. 2.292.8 Disposal of the machine1. Sort the machine, the accessories and the packaging for environmentally friendly recycling.2. Do not